BestBuyZone
Product Cover RGBWW 6 Pin LED Strip Connectors 12mm RGB+CCT Connector - DIY Strip to Wire Solderless Quick Connection for 12v 24v Waterproof IP65 RGBCCT Led Strip Lights (Pack of 10)

RGBWW 6 Pin LED Strip Connectors 12mm RGB+CCT Connector - DIY Strip to Wire Solderless Quick Connection for 12v 24v Waterproof IP65 RGBCCT Led Strip Lights (Pack of 10)

$16.78
$16.78
For Bulk orders
Quantity


  • Features
  • Description
  • Similar Items
Alightings 6 pin LED connector suitable for 12mm rgb+cct LED strip lights. One end connect 6-conductor flat extension cable and another end for rgbww led strip with 6 soldering pads on 12mm wide FPCB. The led strip connectors can not work with 10mm led strip, 3528 rgb led strip, or non-standard 22 awg wire.

The rgbww 6pin connectors can penetrate 6pin 12 mm PCB board and 20 gauge wire without stripping. Compatible with both 5v 12v and 24v 5050 led strip, normal glue coated waterproof 5 Channel LED strip: RGBWW (5 in 1), RGB + Warm White + Cold White (30~90 SMD per meter), Other IP65/IP54 LED strips 12mm with 6 solder pad.

DIY rgb+cct led strip to wire connector with length you want, no more worry extension distance from the strip light to led controller or power supply. A standard 20 AWG wire is recommended for a better experience. The clear cap of the connector must be pressed with pliers and pressed several times to ensure that the pin needle pierces the wire and the PCB and achieves a good connection.

Powerful, reliable, safe and easy to use, avoid difficult and dangerous soldering iron operations. As much as 5A ( R,G,B,W,W 5 channel ) supported, allow you to connect longer LED strip by one connector.

If your led light strip is NON-WATERPROOF or NON-STANDARD WATERPROOF rgbww led strip (too soft or too thin ), pls refer to this item (ASIN:B07Y8N8C5N)

Binding:


Brand:

Biantie La

EAN:


Label:

Alightings

Manufacturer:

Alightings

Model:


Size:

For RGB+CCT 12mm Waterproof

Warranty:


RGBWW /RGB+CCT LED Strip Connector 6 Pin 12mm
A 6 pin solderless flexible strip light connector designed to connect led strip lights to 6 conductor extension cable. No need stripping wire insulation with IPC (insulation-piercing contact) technology. Determine wire gauge and length as you want in linear lighting project with this connector. Powerful, reliable, safe to use, avoid difficult and dangerous soldering iron operations. Allow you to connect longer LED strip by one connector.

Technical Data
Working Voltage:Below 24V
Max Current of Pin: 5A
Pin Quantity: 6 pin
Workable Wire Gauge: 0.34~0.52 mm² (about 20AWG )
Workable PCB Thickness:0.2~0.35 mm
Workable Strip Light Width: 12mm
LED Strip Types: RGBWW / RGB+Dimmable with 6 soldering pads
Waterproof Rating of Applicable LED Strip Light: IP65/IP54
Working Ambient TEMP.: -20~50℃
Heat Resistance:105℃
Connector Dimension: 24*17*7 mm

Note:
1.Does not apply to single-sided circuit board light strip!
2.Non-standard 22 gauge wire is not recommended!

Installation TIPS:
Strip End:
1. Cut the strip straight perfectly, then fully open the clip.
2. Push the strip in until it hits the backing, and pins on the connector make contact,and press hard down for several times with nose pliers to make sure the PINS puncture through the led strips.
Wire End:
1. Have to be separated the 6 wires before you insert them into the connector.
  2. Required to press down hard for several times with nose pliers! Ensure the contacts pierces through the insulation on the wire as there are so many non-standard wires on the market!
3. Reminder: no stripping of the wires.  Just be sure polarity nodes are matched up "+" to  "+" and "-" to "-".
If you have any problem about installation, pls feel free to contact me.

Package: 
10pcs RGBWW Strip to Wire Connectors